Order: 501-562-0337 or trevor@rovahfarm.com
 
 

Series Trucks - Axles, Suspension and Steering
Page 2
  Engine <> Flywheel & Clutch <> Gearbox & Propshaft <> Axles Suspension and Steering <> Brakes & Brake Controls <> Fuel, Exhaust, Emmission Systems <> Cooling & Heating <> Electrical, Washers-Wipers, Instruments <> Chassis, Subframes, Bodyshell, Fittings <> Facia, Trim, Seats and Fixings <> Screws, Nuts, Bolts
  Series axles, suspension & steering -
Page 1 <> Page 2 <> Page 3 <> Page 4 <> Page 5
     
 
 
     
  Axle Breather - Brass  
  Ref: 515845 / Price $10.75  
 
Application: Series (all) - Brass
 
 
  Remote Axle Breather  
  Ref: 595473 / Price $16.75  
  Application: Series - Hose Length 40"
 
 
  Axle Breather Banjo Bolt  
  Ref: 595478G / Price $7.95  
  Application: Series
 
 
  Stub Axle - Front  
  Ref: 599827 / Price $58.95  
  Application: Series II, IIa and III up to July 1980 - Use Bolt #237339
 
 
  Stub Axle - Rear  
 

Ref: 599828 / Price $168.95

  
  Application: Series II, IIa and III up to July 1980, 88" and 109" - Use Bolt #237339
 
 
  Stub Axle - Rear  
  Ref: FRC3132 / Price $65.95  
  Application: Series III - Rear - Post October 1980 - Superceded from FRC3924
 
 
  Stub Axle Distance Piece 'OE'  
  Ref: 599698 / Price $9.95  
  Application: Series 88 and 109 up to Sept 1980
 
 
  Gasket - Swivel Pin Housing  
  Ref: 277289 / Price $1.29  
 

Application: Series II, IIa and III
Description: Gasket between swivel pin housing and stub axle. S/s from GFG108

 
 
  Gasket - Stub Axle Rear  
  Ref: 500978 / Price $0.89  
  Application: Series (all) to 1984
Description: Gasket between rear stub axle and rear axle
 
 
  Hub Assembly  
  Ref: 576844 / Price $129.00  
  Application: Series 1971 onwards - Can be used on earlier trucks but the drum would also need changing to accomodate the larger wheel studs
 
 
  Hub Bearing and Oil Seal Kit - 'NTN' up to September 1980  
  Ref: RTC3534G / Price $106.95  
  Application: Series 88 & 109 up to September 1980
Description: All parts for the rebuild of one hub assembly using NTN bearings and a Corteco oil seal.
 
 
  Hub Bearing and Oil Seal Kit - up to September 1980  
  Ref: RTC3534 / Price $40.95  
  Application: Series 88 & 109 up to September 1980
Description: All parts for the rebuild of one hub assembly.
 
 
  Hub Bearing and Oil Seal Kit - Timken/Corteco from October 1980  
  Ref: RTC3537G / Price $55.95  
  Application: Series 88 & 109 from October 1980
Description: All parts for the rebuild of one hub assembly using Timken bearings and Corteco oil seal.
 
 
  Hub Bearing and Oil Seal Kit - from October 1980  
  Ref: RTC3537 / Price $39.95  
  Application: Series 88 & 109 from October 1980
Description: All parts for the rebuild of one hub assembly.
 
 
  Hub Seal - Rear - Series One  
  Ref: GHS166 / Price $4.68  
  Application: Series One Rear Hub Seal - Superceded from 522287, 236923
 
 
  Hub Oil Seal S2 + 3  
  Ref: RTC3510G / Price $10.75  
  Application: Series 2 - 3
High quality replacement seal from Corteco used on front and rear 88" hubs up to September 1980 and 109" front and rear hubs up to September 1980
 
 
  Hub Oil Seal S2 + 3 - LEATHER  
  Ref: RTC3510L / Price $7.75  
  Application: Series 2 - 3
High quality metal and leather replacement seal for the purist from Britpart used on front and rear 88" hubs up to September 1980 and 109" front and rear hubs up to September 1980
 
 
  Hub Oil Seal S2 + 3  
  Ref: RTC3510 / Price $3.49  
  Application: Series 2 - 3
Seal by 'Allmakes' used on front and rear 88" hubs up to September 1980 and 109" front and rear hubs up to September 1980
 
 
  Inner Hub Bearing  
  Ref: RTC3416G / Price $47.95 - 'NTN'  
  Application: Series 88 & 109 up to September 1980
 
 
  Inner Hub Bearing  
  Ref: RTC3416 / Price $19.75  
  Application: Series 88 & 109 up to September 1980
 
 
  Outer Hub Bearing  
  Ref: RTC3426G / Price $40.95 - 'NTN'  
  Application: Series 88 & 109 up to September 1980
 
 
  Outer Hub Bearing  
  Ref: RTC3426 / Price $14.95  
  Application: Series 88 & 109 up to September 1980
 
 
  Hub Oil Seal Series 3  
  Ref: RTC3511G / Price $11.75  
  Application: Series 3
Seal by 'Corteco' used on front and rear 88" from October 1980 and 109" front and rear hubs from October 1980
 
 
  Hub Oil Seal Series 3  
  Ref: RTC3511 / Price $3.49  
  Application: Series 3
Seal by 'Allmakes' used on front and rear 88" from October 1980 and 109" front and rear hubs from October 1980
 
 
  Hub Oil Seal  
  Ref: FRC2308 / Price $8.75  
  Application: Forward Control 101
 
 
  Bearing - Hub Front/Rear  
  Ref: RTC3429G / Price $20.75 - Timken  
  Ref: RTC3429 NLA - Use STC4382  
  Application: Series III from October 1980. Highest quality aftermarket bearing by 'Timken'. Quality aftermarket bearing by Allmakes/DPI - 2 required for each hub, 4 per axle. Note:

The STC4382 (the later number) can be used in place of RTC3429 without an issue.
However RTC3429 (the old number) can not be used in place of STC4382 as RTC3429 is 1mm thicker.


Timken $20.75
 
STC4382 $11.95
 
 
  Key Washer  
  Ref: 217352 Price $1.85  
  Application: Series (all) from Allmakes
 
 
  Hub Lock Nut  
  Ref: FRC8700G / Price $3.99  
 

Application: Series (all)
Description: Hub nut
 
 
  Hub Lock Nut  
  Ref: FRC8700 / Price $2.50  
 

Application: Series (all)
Description: Hub nut
 
 
  Hub Nut Spanner  
  Ref: 606435 / Price $10.95  
  Application: Series (all) - UK manufactured
 
 
  Lock Washer  
  Ref: 217353 / Price $0.89  
  Application: Series (all)
 
 
  Gasket Hub Flange  
  Ref: 231505 / Price $0.50  
  Application: Series (all) Superceded from GFG106

 
 
  Felt Hub Seal  
  Ref: RTC3515 / Price $1.40  
  Application: Series 88" front and rear up to 1980 and S/s from GHS1002
 
 
  'O' Ring Hub Seal  
  Ref: RTC3516 / Price $0.67  
  Application: Front and Rear 109" excl 109V8 and 88" from October 1980
Description: Rubber 'O' Ring 1 13/16" OD
 
 
  Spiralox Ring - Front Hub  
  Ref: 556445 / Price $0.55  
  Application: Series III 109 and Series 88" from July 1980
 
 
  Spacer Ring - Front Hub  
  Ref: 556628 / Price $3.75  
  Application: Series III 109 and Series 88" from July 1980
 
 
  Circlip - Salisbury Axle  
  Ref: 549473 / Price $0.75  
  Application: Series 109 rear hubs, 88" from July 1980 & front hub 109V8
 
 
  Split Pin - Series  
  Ref: PS608101L / Price $0.49  
  Application: Series (all)
 
 
  Castle Nut  
  Ref: 3259 / Price $1.75  
  Application: series (all)
 
 
  Driving Member 88"  
  Ref: 571235 / Price $24.95  
 

Application: Series II and III up to June 1980

 
 
 
  Driving Member 88 and 109"  
  Ref: 571711 / Price $18.50  
 

Application: Series III 88" from 1980, 109" and 109 V8 up to September 1983

 
 
 
  Driving Member Bolt  
  Ref: 215331 / Price $1.49  
  Application: Series (all)
 
 
  Spring Washer - Driving Member Bolt  
  Ref: WM600061L / Price $0.15  
  Application: Series (all) and other aps
 
 
  Dust Cap  
  Ref: 219098 / Price NLA  
  Application: Series Trucks
Description: Axle Dust Cap
 
 
  Dust Cap  
  Ref: 219098B / Price $2.50  
  Application: Series Trucks
Description: Axle Dust Cap from Britpart
 
 
  Stud 9/16" (screw in)  
  Ref: 561590 / Price $1.25  
  Application: Series 1948 - 1971 uses lug nut 217361 or 576103
 
 
  Stud 9/16" (Push In)  
  Ref: 561886 / Price $2.80  
  Application: Series 1948 - 1971 uses lug nut 217361 or 576103 - Can be used to replace damaged hole for 561590
 
 
  Stud 16MM (push in)  
  Ref: 576825 / Price $2.89  
  Application: Series late IIa and III
 
 
  Wheel Hub Stud - 60mm 'OE'  
  Ref: FRC7577 / Price $13.45  
  Application: Series for Wolf Rims
 
 
  Inner Tube - HD  
  Ref: DA3000 / Price $29.95  
  Application: Series (all) 700/750 X 16" rims. Fits tires 7" to 7.5" wide
 
 
  Lug Nut - 15/16  
  Ref: 217361 / Price $1.15  
  Application: Early Series 15/16" Lug Nut - Fits screw in stud 561590
 
 
  Lug Nut  
  Ref: 576103 / Price $1.75  
  Application: Series 1969 - 1971 - 1 1/16" Lug Nut - Fits screw in stud 561590
 
  Lug Nut OE 16MM  
  Ref: RRD500010G / Price $2.50  
  Application: Series III, Defender, Disco I (steel wheels) - Fits push in stud 576825
 
 
  Lug Nut - Aftermarket Allmakes 16MM  
  Ref: RRD500010 / Price $1.20  
  Application: Series III, Defender, Disco I (steel wheels) - Fits push in stud 576825
 
 
  Wheel Wrench - 15/16" Head  
  Ref: 537179 / $24.50  
  Application: Series (all) 1 1/16"
13" long. For Lug Nut 217361
 
 
  Wheel Wrench  
  Ref: LR011870 / $7.95  
  Application: Series (all) 1 1/16"
13" long. Fits 576103 and RRD500010
 
 
  Wheel Wrench - HD  
  Ref: LR011870A / $13.95  
  Application: Series (all) 1 1/16"
15.5" long. Fits 576103 and RRD500010 - Set further back from the rim, and angled unlike other models to eliminate skinned knuckles. Believe me I learned the hard way!
 
 
     
     
 
 
     
  Series axles, suspension & steering -
Page 1 <> Page 2 <> Page 3 <> Page 4 <> Page 5
   
  Engine <> Flywheel & Clutch <> Gearbox & Propshaft <> Axles Suspension and Steering <> Brakes & Brake Controls <> Fuel, Exhaust, Emmission Systems <> Cooling & Heating <> Electrical, Washers-Wipers, Instruments <> Chassis, Subframes, Bodyshell, Fittings <> Facia, Trim, Seats and Fixings <> Screws, Nuts, Bolts