Order: Cell: 207-214-6133 or trevor@rovahfarm.com
 

 Series Trucks - Flywheel & Clutch
Page 1
  Engine <> Flywheel & Clutch <> Gearbox & Propshaft <> Axles Suspension and Steering <> Brakes & Brake Controls <> Fuel, Exhaust, Emmission Systems <> Cooling & Heating <> Electrical, Washers-Wipers, Instruments <> Chassis, Subframes, Bodyshell, Fittings <> Facia, Trim, Seats and Fixings <> Screws, Nuts, Bolts
     
  Series - Flywheel & Clutch - Page 1 <> Page 2
     
  Pedal Shaft  
  Ref: 272712 / Price $49.95  
  Application: Series II and IIa without servo
 
 
  Bush  
  Ref: 272714 / Price $16.85  
  Application: Series clutch pedal bush
 
 
  Connecting Tube - Clutch  
  Ref: 561661 / Price $61.95  
 

Application: Series II - IIa - Connection Tube Clutch Cross Shaft


 
 
  Pin - Connecting Tube  
  Ref: 536803 / Price $4.95  
  Application: Series II and IIa - 2 required
 
 
  Bush - Clutch Cross Shaft  
  Ref: 214794 / Price $24.95  
  Application: Series II and IIa
 
 
  Seal, Cross Shaft  
  Ref: 90214787 / Price $15.78  
 

Application: Series II and IIa crossshaft seal.
Description: seal outer diameter 1 3/8" inner 9/16"



 
 
  Bush Cross Shaft  
  Ref: 214793 / Price $28.95  
  Application: Series II and IIa crossshaft bush
 
 
  Clutch Master Series Cylinder 2A    
  Ref:  90569126G / Price: $98.95  
  Application: Series 2A models with remote reservoir. Description: Lucas - TRW clutch master cylinder with cast iron body. Also used as brake master on some models - see brake section. Approximate dimensions: Length of body 130mm, pushrod 80mm, bore 19mm (3/4"), mounting centers 57mm.

 
 
  Clutch Master Cylinder Series 2A - replacement  
  Ref:  90569126 / Price: $34.95  
 

Application: Series 2A models with remote reservoir. Description: Plain box clutch master cylinder with cast iron body. Also used as brake master on some models - see brake section. Approximate dimensions: Length of body 130mm, pushrod 80mm, bore 19mm (3/4"), mounting centers 57mm. 


 
 
  CV Master Rebuild Kit "TRW"  
  Ref: STC500090G / Price $22.50  
  CV Rebuild Kit superceded from 8G8837L
 
 
  CV Master Rebuild Kit  
  Ref: STC500090 / Price $4.00  
  CV Rebuild Kit superceded from 8G8837L
 
 
  Adaptor  
  Ref: 139082 / Price $8.95  
  Application: Series Clutch and Brake Master Cylinder Adapter - 3/8" UNF male to 7/16" UNF female - use copper washer 233220 to seal
 
 
  Clutch Master Cylinder - "GIRLING"  
  Ref:  STC500100GIRLING / Price:$164.95  
 

Application: Series 3 and Defender. Can be retro fitted to Series 2A. Description: Clutch master cylinder from GIRLING. Bore diameter 3/4" (19mm). Superceded from 550732 - Rebuild Kit 8G8837L superceded to STC500090

 
 
  Clutch Master Cylinder - "LUCAS/TRW"  
  Ref:  STC500100G / Price:$63.77  
 

Application: Series 3 and Defender. Can be retro fitted to Series 2A. Description: Clutch master cylinder by Lucas - TRW. Bore diameter 3/4" (19mm). Superceded from 550732 - Rebuild Kit 8G8837L superceded to STC500090


 

 
 
  Clutch Master Cylinder  
  Ref:  STC500100 / Price:$26.95  
 

Application: Series 3 and Defender. Can be retro fitted to Series 2A. Description: Aftermarket Clutch master cylinder from Allmakes. Bore diameter 3/4" (19mm). Superceded from 550732 - Rebuild Kit 8G8837L superceded to STC500090

 
 
  Cap - Fluid Reservoir  
  Ref: SJL500030 / Price $5.25  
  Application: To fit STC500100 - Superceded from STC976
 
 
  Clutch Slave Cylinder Series 2/2A  
  Ref:  266694G / Price: $196.75  
 

Application: Series 2 and 2A models with part syncromesh gearbox. Description: 'GIRLING'' clutch slave cylinder which is mounted vertically in bracket on right hand side of gearbox. This cylinder has body of cast aluminium alloy. Approximate dimensions: overall length 110mm, bore 22mm(7/8"), mounting bolts approx 66mm centers. Use clutch hose RTC3386 or 219824 if a late 60's Series IIA NADA with brake booster and 1/4" Clutch Line

 
 
  Clutch Slave Cylinder Series 2/2A  
  Ref:  266694 / Price: $37.95  
 

Application: Series 2 and 2A models with part syncromesh gearbox. Description: Aftermarket clutch slave cylinder which is mounted vertically in bracket on right hand side of gearbox. This cylinder has body of cast aluminium alloy. Approximate dimensions: overall length 110mm, bore 22mm(7/8"), mounting bolts approx 66mm centers. Use clutch hose RTC3386

 
 
  Slave Cylinder Rebuild Kit - NLA  
  Ref: 8G8600LG / Price $9.95  
  Application: Slave Cylinder 266694D and 561231
 
 
  Slave Cylinder Rebuild Kit  
  Ref: 8G8600L / Price $5.62  
  Application: Slave Cylinder 266694D and 561231
 
 
  Gasket - Copper  
  Ref: 233220 / Price $0.95  
  Application: Series master and slave used to seal between union and master and union and slave, ID 3/8"
 
 
  Gasket - Copper  
  Ref: 216914 / Price $1.39  
  Application: Series III. Used to seal between blanking plug and union. ID 7/16"
 
 
  Clutch Slave Push Rod - Genuine  
  Ref: 537601 / Price $48.95  
  Application: Series II and IIA.
 
 
  Clutch Slave Cylinder Series 3 and Defender 4 cylinder - DELPHI  
  Ref:  591231G / Price: $48.95  
  Application: Series 3 four and six cylinder engines. Defender four cylinder engines in conjunction with LT77 gearbox, up to approximately 1994. Delphi PJH120 clutch slave cylinder with cast iron body. Approximate dimensions: Overall length 115mm, bore 22mm (7/8"), mounting centers 63mm.  Use hose RTC4425 or RTC5940
 
 
  Clutch Slave Cylinder Series 3 and Defender 4 cylinder 'TRW'  
  Ref:  591231T / Price: $54.95  
  Application: Series 3 four and six cylinder engines. Defender four cylinder engines in conjunction with LT77 gearbox, up to approximately 1994. 'TRW' clutch slave cylinder with cast iron body. Approximate dimensions: Overall length 115mm, bore 22mm (7/8"), mounting centers 63mm.  Use hose RTC4425 or RTC5940
 
 
  Clutch Slave Cylinder Series 3 and Defender 4 cylinder   
  Ref:  591231 / Price: $20.30  
  Application: Series 3 four and six cylinder engines. Defender four cylinder engines in conjunction with LT77 gearbox, up to approximately 1994. Aftermarket clutch slave cylinder with cast iron body. Approximate dimensions: Overall length 115mm, bore 22mm (7/8"), mounting centers 63mm.  Use hose RTC4425 or RTC5940
 
 
  Slave Cylinder Rebuild Kit - 'TRW'  
  Ref: 8G8600LG / Price NLA  
  Application: Slave Cylinder 266694D and 591231
 
 
  Slave Cylinder Rebuild Kit  
  Ref: 8G8600L / Price $5.62  
  Application: Slave Cylinder 266694D and 591231
 
 
  Slave Sealing Gasket / Spacer  
  Ref: 591988 / Price $3.55  
  Application: Series
 
 
  Slave Bleed Pipe  
  Ref: HD12 / Price $15.95  
  Application: Series III - 12" long 3/8 male / 7/16 female - "Kunifer" Equivalent to 594776
 
 
  Clutch Flex Hose Series IIA NADA Late  
  Ref: 219824GIRLING / Price $59.00  
 

Application: Series IIA -Used on the later NADA Series IIa - Truck will have a brake booster and 1/4" Clutch line to a brass banjo fitting to the slave.

 
 
  Clutch Flex Hose  
  Ref: RTC3386 / Price $11.95  
  Application: Series II and IIa to 1968 - Replaces 268493 and GBH134
Description: Replacement flexible clutch hose, overall length 15.5"
 
 
  Clutch Flex Hose  
  Ref: RTC4425 / Price $11.95  
  Application: Series IIa from 1969
Description: Replacement flexible clutch hose, overall length 13.0"
 
 
  Clutch Flex Hose  
  Ref: RTC5940 / Price $11.09  
 

Application: Series III
Description: Replacement flexible clutch hose, overall length 10.0"

 
 
  Washer  
  Ref: 90512651 / Price $0.65  
  Application: Series III use for flex hose RTC5940 (2) required
 
 
  Nut  
  Ref: NT607041L / Price $0.99  
  Application: Use for both Series II and III use for clutch flex hose S/s from 216912 - Genuine
 
 
     
  Series - Flywheel & Clutch - Page 1 <> Page 2
     
 

Engine <> Flywheel & Clutch <> Gearbox & Propshaft <> Axles Suspension and Steering <> Brakes & Brake Controls <> Fuel, Exhaust, Emmission Systems <> Cooling & Heating <> Electrical, Washers-Wipers, Instruments <> Chassis, Subframes, Bodyshell, Fittings <> Facia, Trim, Seats and Fixings <> Screws, Nuts, Bolts